NI-488 Error Code Family
Below are all of the Error Codes that belong to the NI-488 Error Code Family (see Error List for list of Families).
| Code | Description |
|---|---|
| -37062 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37061 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37060 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37059 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37058 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37057 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37056 | This GPIB device is not a genuine National Instruments product and is not supported by the installed NI-488.2 software. |
| -37055 | Interface DMA test failed. |
| -37054 | Interface interrupt test failed. |
| -37053 | Interface I/O test failed. |
| -37052 | An unknown GPIB hardware error has occurred. |
| -37051 | An unknown NI-488.2 software problem has occurred. |
| -37050 | Invalid IP address or hostname for the ENET interface. |
| -37009 | GPIB Analyzer received an invalid overflow interrupt packet |
| -37008 | GPIB Analyzer received a buffer that is smaller than one USB packet |
| -37007 | GPIB Analyzer detected data overrun |
| -37006 | GPIB Analyzer driver version does not match the firmware version |
| -37005 | GPIB Analyzer received an invalid response (opcode) from the firmware |
| -37004 | GPIB Analyzer received an unknown firmware error |
| -37003 | GPIB Analyzer capture started before it has been configured |
| -37002 | GPIB Analyzer received invalid arguments |
| -37001 | GPIB Analyzer capture is not in progress |
| -37000 | GPIB Analyzer capture is in progress |
| 0 | Error connecting to driver or device. The NI-488.2 driver may not be installed. |
| 1 | Command requires GPIB Controller to be Controller-In-Charge. |
| 2 | No Listeners on the GPIB. |
| 3 | GPIB Controller not addressed correctly. |
| 4 | Invalid argument or arguments to function call. |
| 5 | Command requires GPIB Controller to be System Controller. |
| 6 | I/O operation aborted. |
| 7 | Nonexistent GPIB interface. |
| 8 | DMA hardware error detected. |
| 9 | DMA hardware uP bus timeout. |
| 10 | Asynchronous I/O operation in progress. |
| 11 | No capability for operation. |
| 12 | File system operation error. |
| 13 | Shareable board exclusively owned. |
| 14 | GPIB bus error. |
| 15 | Serial poll byte queue overflow. |
| 16 | SRQ stuck in ON position. |
| 17 | Unrecognized command. |
| 19 | Board not present. |
| 20 | Table error. |
| 21 | Interface is locked. |
| 22 | Ibnotify callback failed to rearm. |
| 23 | Input handle is invalid. |
| 24 | GPIB-ENET already configured. |
| 25 | Event notification was unregistered. |
| 26 | Wait in progress on specified handle. |
| 27 | Event notification was cancelled due to a reset of the interface. |
| 28 | Interface has lost power. |
| 30 | No GPIB address input. |
| 31 | No string input (write). |
| 32 | No count input (read). |
| 40 | Out of memory (MacBus read or write). |
| 41 | Insufficient memory (MacBus read or write). |